Quick calculations for bending, tension, compression, torsion and impact of barsBack to top page
⚠ This tool is only a simplifiedsimulation. It does not necessarily predict every real phenomenon correctly (stress concentration, fatigue, creep, initial imperfections in buckling, joints, anisotropy, effects of environment, temperature and humidity, lot-to-lot variation, manufacturing defects, etc.). Treat the results as reference values for design decisions, and for important applications always verify them by experiments, tests and expert review.
How to use Enter ① shape → ② material → ③ loads (“4 Supports and loads”) in order. Then press “Calculate” on the right (after that, changing any input recalculates automatically). You don’t need to open the “Advanced settings”.
1Shape
mm
Drop an STL / OBJ here, or click to choose
Corrects the tilt so the fixed-end face is perpendicular to the member axis.
Advanced: enter tilt manually
°
°
°
Not loaded
2Material
mass %
HB
Advanced: material properties (filled in automatically)
GPa
MPa
MPa
MPa
g/cm³
°C
°C
Advanced: service temperature and degradation
°C
Temperature table (optional): one “temperature, E ratio, strength ratio” per line. Use “-” if the strength ratio is unknown.
A uniform reduction factor for the whole material (e.g. 0.8 to assume 20% lower strength).
n and k are rough values. Adjust them to match test results.
Calculates a composite with “2 Material” above as the matrix plus filler.
wt%
Advanced: factors and filler properties
GPa
g/cm³
MPa
The factors are textbook estimates. Check them by measurement for each matrix–filler combination.
Use when only some segments differ in stiffness/strength (up to 3 segments). For unused segments, set start and end to the same value.
From (%)To (%)Stiffness (E) ratioStrength ratio
Segment 1
Segment 2
Segment 3
Ratios are multipliers relative to the normal part = 1 (0.7 for 70% strength).
4Supports and loads
N
%
N/mm
Advanced: multiple loads, distribution range, axial force, torque
N
%
N
%
N
%
%
%
N
N·m
mm
mm
e: offset of the line of action of the axial or lateral load from the centroid.
Advanced: object orientation, load direction, position units
°
°
°
Rotations are applied in X → Y → Z order and affect the direction of self-weight.
°
θ=0° points downward from the top of the section.
kg
mm
m/s
J
N
%
mm
G
ms
Advanced: ground properties, air drag, dynamic amplification, effective mass
GPa
g/cm³
mm²
×
3D view Wheel to zoom
Advanced: view angles
°
°
Section and stress distribution
Section properties
Load capacity estimates (each acting alone)
Self-weight is not included.
Beam analysis results
Impact evaluation
Assumptions and notes (click to open)
Euler–Bernoulli beam (shear deformation ignored). Valid when the member length is at least about 8 times the section height (length ÷ height ≳ 8). Accurate only when the section changes gradually along the axis (stress concentrations at steps are not considered).
Self-weight is a distributed load from each section’s mass; only its component along the load direction θ (cosθ) is added to bending (lateral and axial components are ignored). It is not included in the impact and load-capacity lists.
All loads are applied proportionally and simultaneously. The criterion is the onset of yield/fracture (ductile: von Mises; brittle: maximum principal stress; tensile and compressive limits are set separately).
The torsion constant J uses formulas for circles, ellipses, rectangles and thin walls, finite differences (Poisson equation) for arbitrary sections, and the thin-walled closed-section approximation (Bredt) for hollow sections.
Asymmetric sections consider only in-plane bending (twisting, lateral-torsional buckling and shear center are ignored). In compression, the buckling load (Euler/Johnson) and second-order amplification are included.
This tool is a simplified simulation and does not necessarily predict every real phenomenon correctly.Treat the results as reference values, and verify them by testing and expert review for important applications.
Carbon steel strength is interpolated from tables by carbon content (normalized / annealed / hot rolled); quenched and tempered values are empirical conversions from hardness. Multi-material sections assume perfect bonding (continuous strain) between regions and ignore residual stress, quench distortion and microstructural transition layers. Filled polymers are estimated by the rule of mixtures and vary greatly with molding conditions, orientation and interface.
Material values are typical. In real design, always consider test values, safety factors, temperature/humidity, fatigue and stress concentration.